5" Thick Insulation Foam Pink

Product Information

Fire rated foam is usually pink in colour, to identify it as different from other types of expanding foam which don’t have the non-combustible qualities. When would you need fire rated foam? This additive will then slowly migrate to the edges of the foam before forming lines on the surface.

It is the responsibility of the installer and individual responsible for the property to ensure that the product selected is suitable for its intended purpose.

The other factors that also require highlighting with PU Foams are the PU foams affect on the cables or plastic pipes (PU may soften CPVC and PB plastic pipes causing failure) - due to the hydroscopic nature of PVC & LSZH and also due to the high heat created within the foam ball or seal.... etc One end of the microscopic anti-static molecule protrudes from the material edge and draws in moisture from the ambient air to allow a conductive path for current to pass through.

Pink Foams especially should be avoided as there is no way after the installation to identify the manufacturer or product used. 10 things to remember about Pink Foam Try not to use them at all. Take care to cut and install fire protection so that it fits exactly. Use proper collars and seals if compartments need to be penetrated. When pink foam has been used on a timber structure the results will bf foams in timber structure the results will be un achieve satisfactory fire-resistant results. Some fire-resistant foams are specifically designed and tested to fill larger gaps. Closely follow the conditions of use stated in the certification if installing a fire-rated foam product PU foams are combustible and generally will only offer fire-stopping properties when used in narrow voids or gapsThis combination of expertise means that whatever your foam requirement, you can source a solution that is not only perfectly tailored to your specific application, but that will also be precisely compatible with your choice of outer container as well. One of the best known fire rated foams on the market is the Blue 60 Foam , which is blue instead of pink, but has the same non-combustible qualities as pink foam. Manufactured to include an anti-static additive, these pink foams give a surface conductivity that will reduce over time. As it is non-combustible, it won’t catch fire and therefore won’t contribute to the spread of fire through a building. Fire rated foam is not suitable for use around pipe and cables as it doesn’t intumesce or expand in extreme heat so the services would burn away and leave a void and thus breach the fire compartment.

If you need advice on the fire rated foam or sealant you need for your project, get in touch with our expert team who will be happy to help you. In addition the PU Foams can affect the dielectric constant of data cabling. Chemical ingress can change the dielectric constant of a cable thus causing a change in the impedance value and causing failures in data transmission. However the change in the dielectric constant may not show up immediately but could occur in a longer time frame. This can be due to the hydroscopic nature of PVC and LSZH cable which can cause a capillary action of the Chemical within the cable.Expanding Foams are not an intumescent, it cannot close or crush a plastic pipe and should never be installed as such. Polyurethane (PU) foam fillers - also known as ‘fire foam’ - are common in construction, but if you use them without properly understanding them they can end up costing you money, creating worse fire risks, and potentially ruin your hard-earned reputation. With no evidence of the installer or products used it is un-likely that any Foam can be warranted by anyone and should be removed and replaced. There is not a one standard does all for expanding fire foams, as they have been tested differently.

Intumescent sealant, on the other hand, does not expand when applied, and only swells up when a fire has broken out and it reaches a certain temperature. In this circumstance, the sealant will then expand and seal a hole to reinstate a wall or door’s fire containment properties. Installing inadequate polyurethane pink foam can result in smoke and fire entering apartments, corridors and any other compartment therefore leading to injury or even death. Evolutions Fire strive to use third-party accredited materials tested for the configurations th ey are going to be installed into.Fire foams are usually tinted pink to distinguish them from other non-fire rated foams, but they’re all different and have varying functions and properties - make sure you’re using the right one. This type of foam typically has a volume resistivity in the range of 10 10 – 10 12 ohms.cms and often has a surface resistivity that is higher still. Nullifire FF197 foam is also well known in the industry and can be used in fire door and concrete applications. The Nike Miler Tops are one of the most popular in the UK right now - with a slim fit, Summer colours & reflective strips, its no surprise why!